KNX IP Secure Router ChangeLog                       ||    KNX IP Secure Interface ChangeLog                
                                                     ||
========================================================================================================================
2.000 (2022-02-23)
                              New:
                                - After a DCHP Server fails to connect, the AutoIP mode is used. When unplugging
                                  Ethernet and re-plug, the devices tries to start with DHCP again.
                                                                    
                              Fixed:
                                - A T_Disconnect message ( L_DATA_REQ) from an tunnel to that tunnel is not
                                  properly answered
                                - Errorlog buffer can stall device when full
                                
1.062 (2021-01-08)
                              New:
                                - Busload > 140% disturbs TP-PHY.
                                  New Autodetection for that case with recovery of PHY
                              Fixed
                                - constant TP bus overload generates an bufferoverun for
                                  TP driver, which forces the system to disable TP-PHY
                                - phys. damaged telgrams dnonot trigger recovery of PHY
                                - secured application without any GA triggers autoreset
        
1.060 (2020-11-25)
                               New:
                               - Detailed busload information (telnet command)
                               - Support for IGMP Snooping
                               
                               Fixed:
                               - Startup doesnot send Time to bus (application)
                               - Summer/Wintertime calculation problem
                               - (rare) telnet crash when disconnecting cable during session
                               - Telnet output for Sntp Query needs an extra wait for correct IP Server address
                                                              
* v1.055
                               New:
                               - OEM Adaptions for special requirements  
                               - Added Timerserver for KNX Communication
                               - Added Mapper Applikation
                               - Externally triggered Secure GAs will be processed
                           |     by application firmware
                               - Set date and time via telnet for timeserver application 

                               Fixed:
                               - Prog-Key generates factoryresets in rare conditions
                               - Date Calculation
                               - Initializing after Dual Stack activation
                               - DHCP Server gets NAK after Re-Sync
                               - Prog-Key generates factoryresets in rare conditions
                               - Date Calculation


* v1.039
                               New:
                               - Yellow LED is on during Flash reorganizing when Factory-Reset is performed
                               - Implementing latest Security Update 
                               - improved PID scan
                               - Adaption to OEM specific features
                               - Improved robustness in heavy load conditions (>80%) during startup 

                               Fixed
                               - SNTP server does not properly answer client request
                               - Date of SNTP server wrong
                               - Telnet Server can kill network socket in rare start conditions
                              
                                                     ||
                                                     ||    Fixed
                                                     ||     - tunaddr set command (telnet) misbehavoir fixed
                                                     ||

* v1.029
                                                     ||  
                                                     ||   - Bugfix programming Interface 
                                                     ||   - Adapting customized requirements of product familyx
                               
                                                     ||
* v1.028                                             ||    * v1.028                                              
New:                                                 ||    - Initial series production                            
- Added "world coupler" functionality (see ETS Help) ||                                                          
- Improved perfomance in heavy load conditions       ||
- Added measurement of TP current                    ||
                                                     ||
* v1.027                                             ||
New:                                                 ||
- Added current consumption in telnet output         ||
- Added internal pcb temperature in telnet output    ||
Fixes                                                ||
- telnet output of secure keys inhibited             ||
- common improvements                                ||
                                                     ||
* v1.026                                             ||
Fixes                                                ||
- SNTP date caculation bug                           ||
                                                     ||
* v1.025                                             ||
- Initial series production                          ||